A Beginner's Guide to Installing a Bathtub

Click Here

How do you really feel in regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?


How to Install a Bathtub Yourself
Mounting a tub isn't exactly rocket science, but it does call for strong plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately hard job. If the old tub is readily obtainable, the job can move easily; if you have to open up a wall to eliminate the old tub as well as position the brand-new bathtub, the task is a lot harder. In either case, the project is within a residence handyman's skills, although you will need an assistant to vacate the old tub and also embeded in the new one. Make sure you have actually qualified on your own for the job and fit attempting it. Instead of working with a service provider to take over a halfway-completed task, it is far better to take into consideration using one prior to you start. Chances are you may need an expert plumber to make tube links.
This write-up will certainly help you set up a new bath tub in your bathroom if you have currently acquired a brand-new bathtub and also don't require to change the arrangement of your previous water system pipelines.
Your tools as well as material checklist need to comprise the following:
  • New Bathtub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipe Caps


  • Preparing for the Installment


    First of all, the supporting framework supplied with the bathroom must be fitted (if required) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is important to make certain that if the tap includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets device to stop strain on the bathtub.
    Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you make use of all of the provided washers.
    Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its last setting.

    Removing Old Touches


    If you require to replace old taps with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be rather bothersome as a result of the limited accessibility that is frequently the case.
    Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a towel all set for the staying water that will come from the pipes. As soon as the supply pipes have been gotten rid of, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this procedure. When the faucets have been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing compound.
    Prior to carrying on to fit the new taps, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.

    Installing the Bath tub


    Making use of both wood boards under its feet, place the tub in the called for position. The wooden boards are useful in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
    The next goal is to make certain that the bath tub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bath tub till the level reads level.
    To install faucets, fit the bottom of the outermost adaptable tap connector to the suitable supply pipeline by making a compression join; then do the same for the other faucet.
    Switch on the supply of water as well as check all joints and also brand-new pipework for leakages and tighten them if required. Fill the bath tub as well as likewise examine the overflow outlet and the typical electrical outlet for leaks.
    Finally, deal with the bathroom paneling as described in the supplier's instruction manual. Tiling and also securing around the bathtub ought to wait until the bathtub has actually been utilized at the very least when as this will certainly resolve it right into its final setting.

    Suitable New Touches


    If the tails of the new taps are plastic, then you will certainly need a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end gives a link to the existent supply pipelines.
    If you need to fit a monobloc, after that you will call for reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
    Next off, place the faucet in the placing opening in the bath/basin guaranteeing that the washers are in place between the faucet and also the sink. Protect the tap in place with the manufacturer offered backnut. Once the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former kind should be linked to the faucet ends first, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.

    Tiling Around the Bath tub


    In the area where the bath satisfies the floor tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to break an inflexible seal, creating the water to penetrate the wall surface in between the bathroom as well as the tiling, causing issues with moisture and feasible leakages to the ceiling below.
    You can choose from a selection of coloured sealers to blend in your fixtures and fittings. They are marketed in tubes as well as cartridges, and can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly load the tub with water prior to securing, to permit the motion experienced when the bathtub is in use. The sealer can crack relatively very early if you do not consider this movement before securing.
    Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly offered on the marketplace. It is suggested to fit the floor tiles making use of water-resistant or waterproof adhesive and cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    A Step-by-Step Guide to Installing a Bathtub

    As a passionate person who reads about Tools You Need to Install a New Bathtub , I was thinking sharing that piece of content was beneficial. Are you aware of somebody else who is inquisitive about the topic? Why not share it. Many thanks for your time. Don't forget to check up our site back soon.


    Need fast action? Dial.

    Leave a Reply

    Your email address will not be published. Required fields are marked *